Follow

Theses/Dissertations from 2017

PDF

Vibration-Assisted Convective Deposition of Binary Suspensions for Structured Coatings, Thitiporn Kaewpetch

PDF

The Effects of Difunctional Urone Catalysis on Selected Non-Halogenated Flame Retardant Synergies of Dicyandiamide Cured Epoxy Resins, Nathan Phillips

Theses/Dissertations from 2016

PDF

Fundamental Studies of Phase Transformations and Mechanical Properties in the Heat Affected Zone of 10 wt% Nickel Steel, Erin Barrick

PDF

Electric field-induced softening of alkali silicate glasses, Charles Thomas McLaren

Theses/Dissertations from 2015

PDF

Weldability and Strength Recovery of NUCu-140 Advanced Naval Steel, Jason Bono

PDF

On the Use of Self-Assembling Block Copolymers to Toughen A Model Epoxy, Yilin Chen

PDF

Microstructural Evolution and Mechanical Properties of Simulated Heat Affected Zones in Cast Precipitation Hardened Stainless Steels 17-4 and 13-8+Mo, Robert Joseph Hamlin

PDF

The Effect of a Passivation Layer on the Anelastic Response of Gold Thin Films, Patrick Holmes

PDF

Determination of Rolling Parameters for Numerical Simulation of Cold Rolling of Nickel Aluminum Bronze, Giuseppe Iorio

PDF

Fracture Behavior of Silica- and Rubber-Nanoparticle-Toughed Epoxies, Amelia Labak

Theses/Dissertations from 2014

PDF

Chemo-Mechanical Control of Neural Stem Cell Differentiation, Emily Rachel Geishecker

Theses/Dissertations from 2013

PDF

Microstructural Evolution and Creep Rupture Behavior of INCONEL® Alloy 740H® Fusion Welds, Daniel Henry Bechetti

PDF

The Extracellular Environment's Effect on Cellular Processes: An In Vitro Study of Mechanical and Chemical Cues on Human Mesenchymal Stem Cells and C17.2 Neural Stem Cells, Meghan E. Casey

PDF

Characterizing the Effect of Substrate Stiffness on Neural Stem Cell Differentiation, Colleen Curley

PDF

Fracture Behavior of Epoxy-Based Hybrid Composites, Daniel Wesley Davies

PDF

Simultaneous Bright-Field and Dark-Field Scanning Transmission Electron Microscopy in Scanning Electron Microscopy: A New Approach for Analyzing Polymer System Morphology, Binay Surendra Patel

PDF

Anodic Aluminum Oxide (AAO) Membranes for Cellular Devices, Anthony Patrick Ventura

Theses/Dissertations from 2012

PDF

Characterization of Intermediate Phases formed between Solid Nickel and Liquid Zinc during Cycling for a Solar Thermal Energy Storage System, Joseph Colter Sabol

PDF

The Influence of Zinc Content, Strain Rate, and Deformation Temperature on the Thermomechanical Compression of Magnesium-Zinc-Cerium Alloys, Andrew Joseph Thome

Theses/Dissertations from 2011

PDF

Industrial Process Design for Manufacturing Inconel 718 Extremely Large Forged Rings, John Frederick Ambielli

PDF

The Influence of Peptide Modifications of Bioactive Glass on Human Mesenchymal Stem Cell Growth and Function, Mohamed Ammar

PDF

Novel Self-Assembling Block Copolymers Versus Traditional Telechelic Oligomers, Lauren Nicole Bacigalupo

PDF

Design and Fabrication of Functionally Graded Transition Joints to Replace Failure-Prone Dissimilar Metal Welds, Gregory J. Brentrup

Theses/Dissertations from 2008

PDF

Evaluating the dimensional stability of optelectronic adhesives, Thomas R. Daugherty

PDF

The use of nanosilica in epoxy resins, Peerapan Dittanet

Theses/Dissertations from 2007

PDF

Heat treatment optimization of high alloy steel castings and welds, Jeffrey D. Farren

Theses/Dissertations from 2006

PDF

The development of low cost GMAW Fe-Al-Cr filler metals for corrosion resistant weld overlay applications, Matthew R. Galler

PDF

Microstructural evolution during flash annealing of hot rolled 6061 aluminum alloys, Neil Hurley

PDF

Development of corrugated thin metal structures for a MEMS-based fiber optic aligner, Jason Todd Iceman

PDF

Investigation of iron-aluminum-chromium as weld overlay coatings for ultra-supercritical coal fired boilers, Joseph Murphy

PDF

Electron-beam lift-off lithography for fabrication of patterned sapphire substrates, Jason T. Perkins

PDF

Study of epoxy toughening in bulk and disbond initiation at epoxy/aluminum interfaces, Xiaohan Zhang

Theses/Dissertations from 2005

PDF

An archaeometallurgical case study of shear fabrication technology, Laura E. (Elizabeth) Limata

PDF

The investigation of the toughness of a Ni-based alloy with Gd enrichment for spent nuclear waste containment systems, Michael J. (Joseph) Minicozzi

Theses/Dissertations from 2004

PDF

Investigation of corrosion resistance of candidate overlay alloys in high temperature low NOx environments, Ryan M. (Mathew) Deacon

PDF

Microstructural investigation of metal-oxide supported gold and gold alloy catalysts, Andrew A. Herzing

PDF

Characterization of the microstructure and corrosion behavior of AL-6XN friction stir welds, Suzanna M. Klingensmith

PDF

Relaxation mechanisms in yttria doped ceria over a broad temperature and composition range, David Laughman

PDF

Corrosion-fatigue cracking behavior of weld clad tubes, Shane A. (Allen) Para

Theses/Dissertations from 2003

PDF

Effect of iron and iron/yttrium codoping on the densification of a-alumina, Michael David Drahus

PDF

Analysis of grinding wheel loading for electroplated cubic boron nitride wheels used with water-based lubricating fluids, Frank C. Gift

PDF

Stability of epoxy/glass interfaces, Orasa Khayankarn

PDF

Microstructural evolution in tin-silver-copper eutectic alloys, Sarah Louise Lewis

PDF

Structure of alkali tungsten tellurite glasses by X-ray photoelectron spectroscopy and LiNbO3 based transparent, nano-composite, glass ceramics, Jong Wook (Austin) Lim

PDF

Solidification cracking susceptibility and microstructural development of Fe-Cu and Fe-Ni-Cu alloys, Fredrick F. Noecker II

PDF

Separation of polymer particles using a hydrocyclone, Sang Huck Park

PDF

A fundamental study of the microstructural development of superaustenitic stainless steel and Ni-base alloys in casting and conventional arc welds, Matthew J. (Joseph) Perricone

Theses/Dissertations from 2002

PDF

Microstructure-property relationships in laser welded microalloyed steel sheet, Goodwin Phillip Anderson

PDF

Characterization and analysis of the localized deformation of 6xxx aluminum alloy extrudates, Steven R. Claves

PDF

Development of an evaluation test of the coated wire feedstock for cold heading products, Mario Ernest Epler

PDF

Role of surface defects on the corrosion behavior of commercial soda-lime silicate glasses, Anju Sharma

PDF

Investigation of the effect of a surface active flux on the microstructure and properties of gas tungsten arc welds made on a superaustenitic stainless steel, Heather M. (Marie) Snow

PDF

A fundamental investigation of process efficiencies in the Laser Engineered Net Shaping (LENS) solid freeform fabrication process, Raymond R. (Robert) Unocic

Theses/Dissertations from 2001

PDF

Sulfur tolerance of bimetallic Pt-Rh/mordenite in low temperature SCR (Selective Catalytic Reduction) using hydrogen characterized by energy-dispersive X-ray spectrometry in analytical electron microscope, Sukwon Choi

PDF

Investigation of iron-aluminum based weld overlay and thermal spray coatings for the protection of boiler tubes in high-temperature low NOx environments, Jonathan Regina

Theses/Dissertations from 2000

PDF

Quantifying elemental compositions in heterogeneous materials using a new imaging SIMS method, William A. Lamberti

PDF

The corrosion of commercial weld overlays in low NOx environments, Melissa A. Lim

PDF

Thermodynamic and solidification modeling of laser welded nickel-based alloys, Brian D. (Dale) Newbury

PDF

Particle included pitting corrosion in artificial particle clusters modeling 2024-T3 and 7075-T6 alluminum alloys, Pêal Ove Pedersen

Theses/Dissertations from 1999

PDF

The effect of chromate on adhesion between epoxy coating and Al substrate, Po-Nien Chen

PDF

Control of tin compositon and mold medium to reduce the severity of microshrinkage in copper-tin sand catings, Timothy D. Selleck

Theses/Dissertations from 1998

PDF

The role of alloying agents with aluminum for materials compatibility with dilute nitrogen trifluoride plasmas, Brian S. Felker

PDF

Shear band propagation in cross linked epoxies, Guldem Guven

PDF

Interfacial fracture toughness and the role of moisture in microelectronic packaging materials, Ryan M. Hydro

PDF

Relationship between chemical composition and film properties of organic spin-on glass, Hsiu-Hung Kuo

PDF

Effect of mode mixity on fracture energy and the observed crack-tip damage zone of a rubber toughened epoxy, Kevin M. Miller

PDF

A study on the stress-relief cracking susceptibility of a new ferritic steel, Jesse G. Nawrocki

PDF

Bimaterial interfacial failure investigation through the use of the constrained blister test, Gary Charles Neumeister

PDF

On the use of the termodynamic work of adhesion to predict adhesive strength, Siriwan Phattanarudee

PDF

The development and characterization of electrochemically processed thermal barrier coatings, Douglas G. Puerta

PDF

SEM-cathodoluminescence studies of ZnDdSe-based quantum well structures, Huili Xing

Theses/Dissertations from 1997

PDF

Fluorinated oxidation of silicon nitride at low temperatures, Yi-pen Chi

Theses/Dissertations from 1996

PDF

The effect of blend morphology on fracture toughness of rubber-modified epoxies, Ying-Chieh Huang

PDF

A study of ion movement in silver iodoborate fast ion conducting glasses at low temperatures, Justin Jones

PDF

Stem investigation of the chemistry and bonding at grain boundaries in Bi doped Cu, Vicki Keast

PDF

Optimization of a 100-KSI yield-strength high-performance steel (HPS) for infrastructural applications, Anthony Bernard Magee

PDF

Optimization of the production of a chromium thin-film AEM-characterization standard by thermal evaporation, Kathleen A. Repa

PDF

Erosion of thermal spray coatings, Brian Schorr

PDF

Gaseous corrosion in low NO [subscript x] environments, Megan C. Slusser

PDF

The effect of heterogeneous nucleation on two dimensional phase transformation kinetics, William Scott Tong

Theses/Dissertations from 1995

PDF

Mixed-mode fracture of organic chip attachment adhesives, Peter Brandenburger

PDF

Oxidation enthalpy measurements for acceptor-doped perovskite materials, Fengxia Ma

PDF

Fluorinated oxidation in submicrometer regions and related phenomena, Humberto Raposo

PDF

A quantitative study of grain growth in CoPt, Ni, and NiFe thin films, Roger A. Ristau

PDF

Studies on the chemical composition and thermo-mechanical processings of high performance steels, Thomas John Todaro

PDF

Structural integrity of cast-aluminum automotive wheels, Ellen E. Youngblood

Theses/Dissertations from 1994

PDF

The diffusion and properties of an amorphous bright chromium deposit on an iron-carbon alloy substrate after 700°C exposure, Richard Paul Baron

PDF

A metallographic study of 18th century woodworking tools from the Williamsburg collection, Donna L. Belcher

PDF

A characterization of BPTEOS glass utilized in VLSI processing, Tracey A. Carbonetto

PDF

Special studies on the thermo-mechanical processing of low- carbon, 100 KSI strength steels, Carl J. Chrisbacher

PDF

A quantitative method for optimizing weld overlay processing paramenters and comparing process performance, John N. DuPont

PDF

The effects of lead on the solidification and preferred orientation of the zinc coating on continuously hot dipped galvanized sheet steel, Richard E. Fraley

PDF

Reaction of Ti, Ti/Ni and Ti/Pt thin films on AlN substrates, Yoshihiko Imanaka

PDF

Weld overlay coatings for erosion control, Boris Feliksovich Levin

PDF

Mechanical behavior of porous mullite and mullite-SiC composites, Jia Liu

PDF

Statistical failure analysis of copper beryllium strip metal springs using a new fatigue test method, W. Drew Peregrim

PDF

The elastic field of an edge dislocation in a two-phase orthotropic medium, Yu-Chung Wu

Theses/Dissertations from 1993

PDF

A model system for the study of chromized coatings, Vishal Agarwal

PDF

Toughening mechanisms in a high temperature cyanate ester resin modified with a thermoplastic polyimide, Michael DiBerardino

PDF

A method for introducing marker bands onto a fatigue fracture surface using a constant K (max) testing procedure, Christopher Ragazzo